WinDRM Docs 1.2 are the latest - the 1.1 copy below is available for legacy purposes.
WinDRM Docs – Release
1.1
was developed by
Cesco, HB9TLK from a relatively new broadcast standard called Digital Radio
Mondiale (DRM) and it’s open source encoder/decoder named DREAM (http://drm.sourceforge.net/). DRM is based on a proven data communications technology
called Coded Orthogonal Frequency Division Multiplexing (COFDM) with Quadrature
Amplitude Modulation (QAM). COFDM uses many parallel narrow band sub-carriers
instead of just one single wide band carrier for transporting the data. As a
result, WinDRM provides an efficient and robust method to exchange information
over HF including Digital Voice. WinDRM utilizes Forward Error Correction (FEC)
and an Automatic-Repeat-Request (ARQ)
mode to ensure error free data transfers. WinDRM runs efficiently under Windows
operating system 2000 and XP. No
modifications are required for modern SSB HF ham transceivers. Current releases of WinDRM software may be
found at www.n1su.com/windrm. Other
digital HF data/picture transfer software such as Digtrx and HamPAL share
the same core ham-DRM standard and therefore are compatible with WinDRM. WinDRM is not compatible with AOR’s ARD 9000/9800
fast radio modem.
The WinDRM GUI (graphic user interface)
5 “State” Radio Buttons - (enabled under program
control only) as follows:
Input/Output
IO – Enabled: Sound card is linked and passing data to the processor. Disabled: Indicates sound card is not compatible and/or PC’s processor is too slow. If not enabled, WinDRM will not decode data.
Frequency
Acquisition
Freq – Enabled: The three FAC reference carriers/pilots (3 bright vertical lines in the waterfall displays) have been found. These correlate with the DC Offset frequency (normally 350Hz) which is graphically shown as a blue vertical line.
Time Synchronization Acquisition
Time – Enabled: Timing acquisition is done. This indicates the search for the beginning of the OFDM symbol has been completed. Disabled: No synchronization, (usually caused by poor SNR) distortion of the transmitted signal and/or receive band pass is too narrow. Note: False indications (flickering) can be caused by AWGN (atmospheric noise) and generally, may be ignored.
Frame Synchronization
Frame - Enabled: Frame synchronization is completed and the start of a DRM frame (400ms) has been found. The Receiver is in synchronization with the transmitting station. Disabled: Lost frequency synchronization due to poor SNR or change in frequency (avoid “tuning” once in sync). Note: False indications (flickering) can be caused by AWGN (atmospheric noise) and generally, may be ignored.
Fast Access Channel
FAC – Enabled: Receiver is in the tracking mode, has received a good Cyclic Redundancy Check (8-bit CRC) and is in synchronization with the WinDRM transmitting station. FAC is a separate logical channel and modulated with 4-Amplitude Quadrature Modulation (4QAM). FAC provides bandwidth spectrum occupancy (2.3/2.5khz), call sign and other DRM transmit parameters for the DRM receiver. Time, Frame and FAC always precede MSC channel data. Disabled: Caused by lost sync, failed CRC, change in frequency and/or distortion of the transmitted signal.
Main Service Channel
MSC
- Enabled: Indicates actual audio and
data bits are being decoded for voice, text message and/or images. MSC may be
modulated using 4QAM, 16QAM or 64QAM (see
Refer to WinDRM’s technical specs at: http://www.qslnet.de/member/hb9tlk/drm_h.html
Files: (download from: www.n1su.com/windrm)
The .wav files must be created using Digitrx or similar program. For docs on how to create these files, go to http://www.kiva.net/~djones/index.htm . Note: These wave files are not necessary to execute WinDRM. WinDRM stores files/pictures with errors in the Corrupt folder. Good, error free Files/pictures are stored in the Pictures folder. Mixer.bin contains data for the sound card’s mixer settings. Settings.txt file stores user settings such as com port, call sign, etc. User files/pictures to be sent may be stored in any directory for transmission, but are normally kept in the WinDRM directory for quick access.
Other files are created by WinDRM include:
bsr.bin
bsr0.bin
bsrreq.bin
bsrreq0.bin
RX_Log.txt
Known specs and definitions:
TX Data rate
Transmit data rate is computed from the 4 digit number found in the SNR box. This is the number of bits transmitted in one MSC frame (400ms). For the DRM TX “Default” setting this is 1047. The Mode box will show B/S/16/0/2.5 for this setting. When multiplied by the bandwidth, the MSC bit rate is 2.675 Kbps (2.5 x 1070). The CODECs (Linear Predictive Coding, SPEEX and Mixed-Excitation Linear Predictive) require at least 2.4Kbps. For data, WinDRM offers a “Speed” mode at a higher bit rate of 4.362Kbps and a “Robust” slower bit rate mode of 1.567Kbps. By changing these DRM TX settings, the MSC protection, Coding, Bandwidth, and Interleave may be carefully chosen to match the transceiver filters and current band conditions. For HF, a good starting point is the default TX DRM setting. Refer to the specs found at: http://www.qslnet.de/member/hb9tlk/drm_h.html
Modulation and Forward Error
Correction
Carriers are modulated using QAM4, 16 or 64 in the MSC. The QAM constellation size is selected by the user under the DRM TX settings. QAM4 is set by WinDRM for FAC since it is the most robust. QAM carriers would appear to be overlapping within their spectrum. However, once they are synchronized at the receiver, they no longer over lap (now orthogonal/unique) and can then be demodulated. QAM has both fixed amplitude and phase modulation. Forward Error Protection (FEC) is provided by Reed Solomon (RS) code. By definition, RS has the ability “…to produce at the sender ‘n’ blocks of encoded data from ‘k’ blocks of source data in such a way that any subset of k encoded blocks suffices at the receiver to reconstruct the source data.” This gives DRM the ability to “repair itself on the fly” by accurately rebuilding the audio or file data as it was originally coded at the transmitter. If this can’t be done, then WinDRM keeps track of the “errors” (missing data) in the file and with the BSR, the data can be replaced with error free data using one of the ARQ features.
Image data transfer time
KA2HZO has provided the following on-the-air transmission times calculated between the click on TX pic and the return to receive. The times represent real throughput capability of WinDRM in the default, robust and speed modes.
File Size Kbytes Mode in Sec=Default Mode in Sec=Robust Mode in Sec =Speed
5 26 40 19
10 44 72 29
15 61 104 39
20 78 135 49
25 95 166 59
The
“Speed” mode can provide better than 2.5 times faster throughput than the
“Robust” mode and 1.5 times faster than the default
PC requirements
Windows OS, 2000 or XP. 700mHz minimum processor speed with 1.2GHz or higher to ensure smooth operation. Avoid executing other programs while WinDRM is decoding or transmitting. For testing/experimenting, most PCs can run two instances of WinDRM in a back-to-back mode (connect sound card line out/speaker to line in/mic and carefully set levels). One instance may then be used to transmit pictures to the other.
Status of received data in the Info box for images (RX Pics)
The “Info” box during receive provides a status of the data being decoded as it is received. These counters are shown in three sets of one to three digits separated with a forward slash (/). The first set is the number of memory segments (size) in the file. The second set shows the number of good segments decoded. The last set shows the segment number of the last segment decoded.
The first set of numbers represents what WinDRM “knows about” at the start of the transmission and will change because the program begins assembling the data before the total is known. If a segment is received in error (CRC failure), a following instance provides the opportunity to receive it again. If received OK, the counter will increment. After all the data is received, the segment counts will all agree indicating the file has been received error free. If a picture was received, it will open up in Irfanview or the viewer/program associated with the file’s extension. Note: The segment size increases with the constellation size (4 thru 64) of the QAM since it is possible to transmit more bits per symbol in the higher order constellations.
Status of received data in the info box for voice (RX)
While receiving voice, the Info block displays 1 to 100% representing the quality of the decoded data. The quality is determined by the number of good frames of data received versus bad since the last synchronization. 70 percent or higher number usually provides sufficient speech quality to understand what is being said for the QSO. With SNRs of 15 or higher, expect a quality number near 100 percent.
Status of transmitted data in the Info box for files (TX Pics)
After transmitting the lead in sync data, the Info box provides the status of the file as it is being sent. The counter consists of two sets of numbers separated by a forward slash (/). First set shows the instance being sent while the second set shows the percentage (1 to 100 percent) of the total segments sent. The number of instances the file will be sent is shown in the “Select File” window. A choice of 1 to 3 may be selected but additional instances can be sent by adding the file in the Select File window more than once.
Status of transmitted data in the Info box for voice (TX)
No data is shown in the Info box during voice transmission except during the lead in sync period.
Info box during “lead in” transmission
In both picture and voice transmissions, lead in sync data is sent to the receiving station for setting up the timing and other OFDM carrier information. This lead in maybe lengthened to provide more set up (sync) time at the receive end by selecting long lead in under the Select Files window. While the lead in is being sent (up to several seconds), the Info box will increment various numbers indicating this data is being transmitted and the actual file data has not started. Some of this data includes determining the size of the file and packetizing data prior to be sent.
Text Message data
Up to 128 ASCII characters (including spacing) may be transmitted. Greater than 128 will be truncated at the receive window. Text messages may not be sent with data (file/picture transmissions). Text messages may be added or changed during TX. The data rate is only 80bps, but the message is continuously transmitted during the voice transmission. In receive, the text message window remains open at the end of the transmission. This message window may be closed at any time. Text messages may only be sent and received with Digital Voice transmissions.
Transmit and Receive parameters (and transceiver setup)
For optimum performance, the OFDM carriers must fit within the band pass of the receiver (and transmitter). The DC Offset of the transmitter’s default of 350Hz was chosen to ensure the 2.5Khz wide OFDM signal is inside both the transmit and receive audio band pass. The 350Hz is an offset from DC (0 hertz) and is the where the carriers of the OFDM “start”. The timing (OFDM searches for this) locks on and starts all its shifting from here for all the 51 carriers. WinDRM does this based DC offset frequency. This offset can be changed but it must chosen so the spectrum will fit within the band pass. If the DC is changed too much from 350, all the OFDM carriers may not fall within the band pass. It is not important to be exactly on frequency. Thirty to fifty hertz off the DC frequency will still allow sync to occur. Low SNR may be caused by carriers outside the receiver’s band pass. Experience has on HF has found that low SNR is usually caused by improper audio levels, QSB, QRN, multi-path or just “weak signals”. If any tuning of the frequency is made during receive, the demodulated signal is phase shifted and attenuated. The orthogonality of the OFDM symbols may also be destroyed and this causes ICI (inter-carrier-interference). Click on “Reset” to re-sync the data if any tuning must be done to bring all carriers within the band pass of the receiver. When the WinDRM users talk on SSB, carefully tune to their frequency. This will ensure you are on the frequency being used for DRM data also. Be sure the receiver’s band pass is at least set to at least 2.5 kHz, no compression (or audio processing) and Fast (or OFF) AGC. For transmit, minimize distortion by avoiding any ALC action. For 100 watt rigs, set power to approximately 15 watts average power. This mode works best with linear transmitters and amplifiers. OFDM has a rather high crest factor caused by the mathematical FFT operation applied to the transmitted signal. The peak power is much higher (6-7 dB) than the average power as read on a wattmeter. Experience has found that operating out of the linear region of your transceiver and/or amplifier may result in a 3 to 4 dB lower SNR at the receiving station. For a detailed explanation of how to set the power out of your transmitter, go to: http://www.tima.com/~djones/DRM_power.htm
CODEC
Select under DRM TX Settings, “CODEC” (voice) or “DATA” (files) being transmitted will be displayed. Under program control, the receiving station will automatically decode and display the mode of transmission being sent (LPC, SPEEX, MELP or Data).
SNR
Signal-to-Noise-Ratio is an estimated value that indicates the quality and strength of the received signal. Experience has found, near error free data may be decoded with a SNR greater than 7.0 dB. The higher the number, the better the signal is being received. An SNR of 10 or better usually ensures error free copy. QRN, QRM, transmit distortion and propagation problems caused by multi-path cancellation lower the SNR. Under “ideal” band conditions with signals over S-9, SNR may rise to 25db or greater. SNR is lowered if the transmitted or received signal’s COFDM carriers are attenuated because of bandpass filters that are too narrow for the bandwidth (BW) chosen.
DC
Refers to the frequency offset from 0 Hz to the start of OFDM carriers. Default is set at 350Hz. This is an arbitrary number chosen to ensure both the 2.3 or 2.5 kHz signal BW “fits” with minimum attenuation inside the bandpass of the receiving station. This may be confirmed by observing the shifted PSD, transfer function displays or the moving waterfall displays. The accuracy of the receiving station’s tuning for the COFDM signal is dependent upon this factor which may allow up to 50Hz tuning error without affecting the decoding process. It is important to note however, that once sync is obtained, no further “tuning” of the signal should be attempted. A blue vertical line indicates the location of DC offset. Values of 50 to 5000 Hz are valid entries but 350 Hz is normally used. The offset plus the BW equals the width of the signal (350+2500 = 2850Hz).
Mode
Displays the DRM TX settings. The default is:
B (DRM Mode B) S (Short Interleave) 16 (Main Service Channel 16 Quadrature Amplitude Modulation) 0 (Protection level) 2.5 (2.5 kHz Bandwidth). Most stations use 2.5kHz since additional carriers are available with this wider BW giving better receive performance. TX modes are selected to correlate with the quality of the signal (as affected by propagation, signal strength, QRN, etc) available at the receiving end. These modes affect the transmission speed and in turn robustness of the received signal. For more info, see “DRM TX Settings” later in this doc.
Setup
Any com port 1 through 8 may be selected for control of the transmitter’s PTT using conventional RS232C data terminal ready (DTR) line. For most applications, a standard RS232C cable is used to connect the PC’s com port to the sound card interface (RigBlaster or equivalent). In addition, the DTR or ready to send (RTS) line may be used to mute the receiver’s speaker while receiving data. Implementation of this feature may be found at KB4YZ’s web site. (http://www.kiva.net/~djones/index.htm ) WinDRM may be started and the PTT controlled in the “Remote” (PTT on CTS or PTT on DSR) mode using the com port’s CTS or DSR line. This Remote mode will allow the use of external switching from the PTT switch on a microphone or a PTT foot switch. To avoid a possible ground loop, an optical isolator or a relay should be used to assert (apply a positive +5 to 12vdc) to either the DSR or CTS line. Note: Due to some ambiguity between Windows OS and WinDRM, the CTS and DSR are reversed (CTS is pin 6 and DSR is pin 8 in the 9 pin Sub-D PC’s com port connector). Use of a pull-down resistor on these pins will help ensure no false PTTs. For com port protection, a current-limiting resistor may be used in series with the positive voltage applied to the DSR or CTS pin. This Remote feature is not saved in WinDRM’s user’s settings file therefore when used, it must be checked each time the program is executed. TX voice may also be activated using the keyboard’s spacebar. With “TX Voice” in focus (as show in above display), taping the spacebar will put WinDRM in transmit (activating PTT) and pushing it again will return WinDRM to receive (a toggle function). To un-focus TX voice and avoid placing WinDRM in transmit while using the keyboard for other functions, push the keyboard’s “Tab” key. Spacebar PTT will not function while in the “Remote” mode.
Setup
Call sign
Up to 8 number/letters may be entered. Properly entered, this provides a valid ID for all transmissions. This meets FCC requirements for station ID. “NOCALL” is the default.
Setup
Display
Receive Spectrum
The Spectrum’s display is approximately 2.5 kHz wide in the horizontal while the vertical shows the amplitude in dB (no scales are shown for any of the displays). The shape of the signal is rectangular and represents the 2.3 or 2.5 KHz band width of the received signal. This display may be used to set the audio input level of the sound card. Too much input will over-drive the sound card (line input should always be used when available) and may cause distortion and low SNR. Carefully adjust the line input level and the receiver audio until the top of the COFDM spectrum averages approximately half way up in the display window. Although there is normally good dynamic range in most sound cards, the goal is obtain the highest SNR reading. After sync has been obtained, a blue vertical line will appear in the spectrum. This blue line shows where the timing for acquiring the COFDM signal has started (the DC offset frequency) which is normally 350Hz. This line may pop up intermittently as it will “false” on random noise and should be ignored when no valid COFDM signal is being received. The three reference pilot carriers are easily seen in the display with frequencies of 725, 1475 and 1850Hz.
Receive Waterfalls
Three waterfalls are available,
Moving, Static, and Flicker reduced. The COFDM spectrum will be shown with an
even intensity level across its 2.3 or 2.5 KHz bandwidth. Within the waterfall,
three FAC reference (or pilot carriers) of higher intensity can be seen. These stand out because they have higher gain
(transmitted at twice the power). These FAC pilots are modulated with known
fixed phases and amplitude which optimize DRM’s performance for initial
synchronization, duration and reliability.
They are used to calculate the initial coarse frequency offset of the
received DRM signal. This is the first part of the COFDM sync process and must
occur before the received DRM signal can be
decoded. The high-lighted red markers of the waterfall’s sweep indicate
where the FAC reference carriers are located when the transmitter and receiver
DC offsets match. The moving waterfall sweeps
from top to bottom with the red marker’s indicating the position of reference carriers
remaining fixed at the top of the display.
The moving waterfall adds a visual method to monitor the health of the
decoded signal in the form of a vertical line on each side of the waterfall
spectrum. During the decoding process, the
green vertical lines indicate data is being received without errors and red
lines indicate errors. These green/red indicators move with the spectrum
instantly showing when and where the data errors occurred. The horizontal line
across the top of this display indicates the bandwidth of the COFDM
signal. The signal in the waterfall
should fully extend the width of this line.
The Flicker reduced Waterfall is a modified moving waterfall designed to
reduce “flicker” from some types of fast LCD or laptop displays. Note: The
waterfall display shown above depicts the effects of multi-path cancellation as
shown by the darkened areas. The
carriers in this area are being attenuated due to these phenomena. The two
bright lines (on the bottom left, just before the start of data) is unwanted
noise (probably caused by a ground loop between the transceiver and the PC
soundcard) on the Speaker Out audio line to the transceiver’s Mic input. Every effort should be made to eliminate this
type of interference when connecting audio cables between the PC and the
transceiver. To minimize ground loop
and/or RFI problems associated with sound cards and the transceiver, refer to these
informative papers found at: http://audiosystemsgroup.com/SAC0305Ferrites.pdf
and http://audiosystemsgroup.com/Ferrites-Ham.pdf
Input Level (receive)
This display graphically shows the received audio. Sound card (recording) Line Input may be set to approximate the level as shown in the display above.
Shifted PSD (receive)
This display plots the “estimated Power Spectrum Density (PSD) of the input signal”. The X axis measures the PSD of 0 to 50dB while the Y axis is frequency from 0 to 12 KHz. Here the incoming DC frequency (350 Hz) is mixed with 5650 Hz to give a 6 KHz (the blue vertical line is correctly shown in DRM mode B only). The peak on the left is the mirror image (5650 – 350 = 5300 Hz) and is partially suppressed by the WinDRM’s internal IF filter. If a peak is displayed between the signal and the mirror signal, a 50/60Hz noise could be in the transmitted audio from ground loop. The three peaks seen at the top of the waveform are the pilot carriers for sync and have twice the power. Any roll off or dips in the waveform indicate the carriers in these areas have a loss of power caused by QSB and/or attenuation in the band pass of the transmitter or receiver. If the transmitter or receiver does not allow the 2.3/2.5khz wide (BW = 350 to 2850Hz) DRM signal to pass without attenuation, this waveform may roll off on either end. For DRM Ham “Low IF Measurements” refer to HB9TLK’s info found at: http://www.qslnet.de/member/hb9tlk/drmif/index.html
Transfer Function (receive)
This plot shows the “squared magnitude of the channel estimation at each sub carrier”. The green line is the transfer function (TF in dB) while the blue line shows the phase distortion of the channel (Group Delay in ms). Optimum signals will yield a flat response and display even/flat lines across the width of the display.
Impulse Response (receive)
This plot shows the “estimated Impulse Response (IR) of the channel based on the channel estimation”. This pulse is used in determining the HF channel’s frequency and phase characteristics so the signal may be restored as close as possible to what it looks like at the transmitter. The time delay of the shortest path is taken as the zero reference for the estimated pulse response.
Fast Access Channel (FAC) Phase (receive)
This plot shows the 4 QAM rectangular constellation. For more info on QAM see above info under FAC radio button and this URL: http://en.wikipedia.org/wiki/Quadrature_amplitude_modulation
.
Main
Service Channel (MSC) (receive)
This plot shows the various constellations for a 4 through 64 QAM logical channel that provides the voice and file data. High SNR keeps the points in a close constellation but some scattering is expected on HF where the Reed-Solomon error correction coding is applied. QAM varies the amplitude and phase of each one of the carriers (for 16 QAM and up). Then, through frequency multiplexing (adding these carriers together across the 2.3/2.5 kHz BW) the OFDM is created. 16QAM is shown here.
Setup
Codec (and Audio Filter)
Either
Linear Predictive Coding (LPC), SPEEX, or Mixed-Excitation Linear Predictive
coding (MELP) CODEC may be selected for digital voice. MELP is the
default. All three require 2.5 kHz/2400bps
minimum (see
Setup
Text Message
Edit TX Text Message
Selecting “Edit TX Text Message” will open up a window to enter text.
Up to 128 ASCII characters (including spacing) may be transmitted. Greater than 128 will be truncated in the receive window. Text messages can not be sent with data (file/picture transmissions). Text messages may be sent, changed or deleted during a voice transmission. The data rate is only 80bps, but the message is continuously transmitted during the voice transmission. This may be used to send your QTH and station info.
Allow RX Text Message (default)
Default provides a window for receiving the transmitted messages. This text message window remains open for further review after the transmission has ended. (for more info, see previous “Edit TX Text Message” description)
Setup
Save Received Files
Checked (default) indicates files received without errors will be saved in the sub-folder of WinDRM named “Pictures”. If a file is missing segments, it will be saved in the “Corrupted” subfolder. Both of these folders are initially created by WinDRM.exe.
Show Received Files
Checked (default) indicates error-free files will automatically be displayed (when associated with a viewer such as Irfanview). Irfanview is the “viewer of choice” and may be downloaded free at www.irfanview.com Irfanview requires a plug-in and must be associated with the image file extensions (.jpg, jp2 etc) to display pictures. In Irfanview, go to Options>Set File Associations>Extensions then select “Images Only” or just check the extensions you wish Irfanview to display. Note: Received files and pictures will be saved in the Pictures or Corrupt folders even if no viewer has been configured.
Show Only First Instance
Checked (default) indicates only a single instance of an error-free file will be displayed when received multiple times.
Soundcard
Opening the mixer will display the sound card’s “Recording” and “Playback” sliders for Audio in and out. These are associated as follows:
RX Input = Mixer Recording Line-In (from receiver speaker out)
TX Output = Mixer Playback Master Volume (speaker out) (to xcvr’s microphone input)
Voice input = Mixer Recording Mic-In (PC microphone into jack on soundcard)
Voice output = Mixer Playback Master Volume (speaker out) (to xcvr’s mic input)
For Digital Voice, inputs are switched under program control (line-in switched to mic-in for transmit). Adjust mixer sliders for proper input and output levels. Start with the “sliders” approximately one-third up. Only the RECORDING microphone should be enabled. For transmit, Master Volume and Wave Out must be selected. Use the Master Volume for the coarse adjustment and Wave out as the fine adjustment. Uncheck all other inputs/outputs. For decoded Digital Voice, Mixer Playback Master Volume must be manually switched to the PC’s amplified speakers. If two sound cards are available, set up one card for Receive and the other for Transmit. No manual switching will then be required. For further help with the Soundcard Mixer, see http://www.sagebrush.com/mixtech.htm
DRM TX Settings
Mode A/B/E (A = Ground wave B = Single to multi hops E = NVIS Multi-hops)
MSC
Protection (
BandWidth (2.3Khz – 2.5Khz)
Interleave (Short 400ms – fast QSB Long 2sec – Slow QSB)
MSC
Coding (
DC Offset (50-350-5000Hz)
Clicking
the Default button will result in the following
Mode MSC Protection Bandwidth
Interleave MSC Coding
DC
B
Robust lowers the transmission BPS by changing 16QAM to 4QAM. Speed raises the transmission BPS by changing Mode to A, MSC protection to Low and Interleave to Long 2 seconds. Long interleave requires additional sync time. Voice requires 2.5kHz bandwidth for the 2400 bps CODECs. 64QAM on a HF channel requires a higher SNR and minimum multi-path to perform well. MSC Protection A, B and E provides different levels of forward error protection (FEC) to protect the MSC from the detrimental effects of QSB/QRM/QRN. B is higher than A with E (known as D in DRM) for Near Vertical Incidence Skywave (NVIS) transmission where the signal is transmitted with a very high angle of radiation short path propagation. In practice, however the extra protection for this mode appears to have limited results. In DRM, Mode A is used for ground wave propagation where Mode B for single hop/multiple hop propagation. The default mode “B” on HF has shown to have the best overall performance.
Note: A BSR request
may be made using different
DRM RX Settings
Default settings are:
Freq.
Acq. Sens. Search
Window Size Auto Reset
60 350 Enabled
Higher settings increase sensitivity for weak signals but with higher probability of false sync. Fast Auto Reset has shown to be effective in providing faster sync recover under poor signal conditions. These settings work well in the default mode, however this is a good area for hams to experiment and find what settings are best under varying signal/band conditions.
BSR (Bad
Segment Report – automated)
BSR provides a procedure to repair (sometimes called a “fix”) a defective file (i.e. picture). Normally, a defective file is caused when the received station does not receive all the memory segments error free (segment failed CRC check). When this happens, clicking on the “BSR” button will open a window and show the number of segments “missing”. The received station may then send a BSR “Request” to the sending station and request these missing segments be resent so the file (picture) may be repaired and displayed. This is the manual method and requires user intervention. The “automated” BSR completely automates this procedure for P2P (point to point) transfer of files. Auto Open BSR request, TX ARQ and RX ARQ must be checked to initiate this procedure. Note: WinDRM does not look for activity on the frequency. The procedure simply relies on timing between the tx to rx and rx to tx change-overs and does not “listen” on the channel for other activity. Therefore, users should maintain control of the station while this automated BSR is being executed, i.e. “attended” operation. Upon a successful Auto ARQ exchange, the sending station will send “Good Copy” to the receive station’s waterfall. Note: Up to 30 additional segments are sent in with the receiver’s BSR. These “additional” segments are sent to ensure the receiving station is in sync. Up to four multiple BSRs windows may be open at one time. There requests may be transmitted one at a time or all can be transmitted by clicking on the “BSR send” button while any one of these request are being made (during transmission).
Load last RX file
When this is selected, the last error free file received will be loaded in the “Select Files” window. This is normally used when the entire file is to be re-sent.
Auto open BSR request
Automatically opens up the BSR window when a defective file is received. This must be checked to initiate the automated BSR procedure.
TX ARQ
Automates the “send” request for the BSR
RX ARQ
Automates
the “receive” request for BSR
BSR (button)
Bad Segment Report
When a picture is received with segments missing, a left click on this button will display the number of segments. Press “OK” to request these segments be re-sent.
SPA (button)
Show Picture Anyway
Left click on this button will attempt to associate and display the last received picture even if it the file is incomplete. If there is enough data for the picture to partially assemble the picture, it will be displayed. Dependent up on the amount of missing data (memory segments) and preference of the received station, the user may then click on the BSR button to show the number of segments missing. Now, the BSR the request can be made to resend the missing data. The picture above is an example of a picture displayed using the SPA with missing segments.
Picture shown “repaired” after receiving the missing 35 segments using the BSR request procedure. Note: This entire procedure may be automated when the “Auto Open BSR,” “TX ARQ” and “RX ARQ” checked.
Example of the transmitting station’s responding to a BSR request. Note: This is not the data used in the previous repaired picture.
G (button – works with Windows XP only)
Good (good picture received)
Left click on G will transmit a pre-recorded wave file displaying “GOOD” in
the received station’s waterfall. Filename: g.wav
B (button – works with Windows XP only)
BAD (bad picture received)
Left click on B will transmit a pre-recorded wave file displaying “BAD” in
the received station’s waterfall. Filename: b.wav
ID (button – works with Windows XP only) Left click on ID will transmit a pre-recorded wave file displaying the transmitting station’s call sign in the received station’s waterfall. Filename: id.wav
For help in creating these wave files, go to KB4YZ’s web site: http://www.kiva.net/~djones/index.htm
TUNE (button)
Left click on TUNE will transmit a pre-recorded wave file for setting the proper output level of the transmitter. Three reference pilot (sync) carriers will be displayed in the received station’s waterfall. From left to right, A=1850Hz, B=1475Hz and C=725Hz. With a properly adjust transmitter (good linearity – not overdriven!), the receiving station will only see these 3 carriers. Any others displayed (at the receiving station) are products of inter-modulation distortion which will degrade performance. For the adverse effects caused by non linear transmissions, see http://www.tima.com/~djones/DRM_power.htm
TX Pic (button)
Left click opens a window to add or remove files for transmission. Radio buttons enable from 1 to 3 instances of the file be transmitted. Additional instances of the same file may be sent by adding the file multiple times in the Select Files window. Long Leadin increases the time for sync data at the beginning of the transmission. This is used in the presence of weaker signal conditions or QRM to help ensure the sync is made at the receiving station prior to sending the file data. Return button closes and returns to the opening WinDRM display. TX button starts transmission of sync data followed by the file data.
TX Voice (button)
Left
click starts voice transmission. The microphone
must be connected to the soundcard’s “MIC” input. The display graphically shows
the transmit microphone level (sound card’s microphone input). Adjust the mixer’s Record slider while
speaking across the PC microphone. Best
results will be found when the microphone input level is kept rather low while
speaking with a loud tone of voice. Keep the average level so peaks fill
approximately 50-75% of the display.
Speaking too loud will cause the display to turn red. Some PC electret microphones have poor
response and tend to accentuate the highs which cause high peaks and
distortion. Experiment in this area to find the best microphone and level for
the highest speech quality. MELP codec has shown to produce the highest speech
quality of the 3 CODECs. The audio filter may help the intelligence of the
speech in some conditions. SPEEX sounds
like it adds more fidelity to the speech (when compared to LPC) but at the same
time, it is a bit muffled and tends to “flat top” the input easier. This is an area where a well chosen
microphone (such as a one from Heil Sound) will improve the voice quality. The input impedance of most sound cards
microphone is approximately 2500 ohms.
This impedance may vary but should be a consideration when choosing a
microphone. Bandwidth under DRM TX Settings must be set for 2.5 kHz. The TX button name changes to “RX” while
transmitting. “Echo” of the decoded voice may be caused by some combinations of
PC and soundcard. This may be a soundcard latency problem related to the timing
and transfer of data or a ground loop.
Changing sound cards may correct this problem. Known “good” sound cards
include
RESET (button)
Reset re-starts the sync process in receive. Normally, this button is rarely needed.
About
Info
About
Help
Typical connections between PC, interface and radio
See
“
Further DRM technical info and software may be found at: http://www.drmrx.org/, (DREAM 1.5cvs 27Nov05) http://rarewares.org/aac.html and www.drmradio.co.uk
--------------------------------------------------------------------------------------------------
updated 01-Dec-2005
© copyright 2005 by Mel Whitten,
KØPFX – mel@melwhitten.com
